Jump to: Troubleshooting Your 1.5 Inch Pool Lights Syncing Issues
Operating pool lights using a wall switch (12 VAC)
The pool light can be manually controlled using a standard wall-mount light switch. Multiple pool lights can be connected via a junction box to a single switch so that all lights can be switched on and off together. The lights are controlled by cycling AC power to the 12VAC transformer from a standard wall switch. The pool lights can also be automatically controlled via Pentair IntelliTouch® and EasyTouch®.
Selecting a light show mode or fixed color
Selecting a light show mode or fixed color Switch power on to the light. A white light will momentarily illuminate, followed by the previously selected color. To select a color show mode (1-7) or fixed color (8-12), turn the wall switch off/on a specific number of times. Each number (1-12) shown below corresponds to the number of times to power-cycle the switch to activate a color light show or fixed color. Example: To select California Sunset Mode; turn the light on, then turn off and on six times. During the off/on switching process, no illumination will occur.
Order of color modes when using on/off switch
1. Sam Mode: Cycles through white, magenta, blue and green colors
2. Party Mode: Rapid color changing building energy and excitement.
3. Romance Mode: Slow color transitions creating a mesmerizing
and calming effect.
4. Caribbean Mode: Transitions between a variety of blues and greens
5. American Mode: Patriotic red, white and blue transition.
6. California Sunset Mode: Dramatic transitions of orange, red
and magenta tones.
7. Royal Mode: Richer, deeper color tones
8. Blue: Fixed color.
9. Green: Fixed color
10. Red: Fixed color.
11. White: Fixed color.
12. Magenta: Fixed color
13. Hold: Save the current color effect during a color light show.
14. Recall: Activate the last saved color effect
Saving a color mode or fixed color
When power is switched off to the color lights, the last color show mode or fixed color will be saved. The next time the light is powered on, the previously saved color show mode or fixed color will be displayed. For example, while in “Party Mode” switch the light off. Wait more than 10 seconds, switch the light back on to resume “Party Mode.”
Hold and recall feature
Hold button/LED: Press this button (LED on) to capture and save a color effect while displaying one of the light show modes. When the button is pressed, the LED will be on, indicating that the color effect is captured.
Recall Button/LED: Use this button (LED on) to activate the last saved color effect. When the button is pressed, the LED will be on, indicating that the color effect is being displayed.
Installation
REPLACING THE GLOBRITE® LIGHT ASSEMBLY (IN AN EXISTING POOL OR SPA)
1. Switch off electrical switch or circuit breaker at the source.
2. Remove Junction Box or Transformer cover. Disconnect the light wires and attach a fish tape to the existing light power cord. This will assist in pulling the replacement light power cord through the conduit back to the junction box.
3. Remove the GloBrite color light assembly from the pool or spa water. Using the provided installation tool, rotate the light assembly counter-clockwise about a 1/8th turn to release the light from the niche. Note: The Life-Bulb 1.5 inch light will come with a light installation tool to assist in this process.
4. Slowly pull the light and attached power cord (with attached fish tape) out of the niche. Pull the light’s power cord and fish tape out of the niche and place the light on the deck.
5. Attach the new light power cord to the fish tape and carefully feed the fish tape and cable to the junction box.
6. Install the light into the niche: Place the light installation tool over the front of the light. Turn the tool and light clockwise while pushing inward, until you feel the stop point. This indicates the light is properly seated, locked and the electrical conduit, is completely sealed. Note: If the light does not turn smoothly, pull the light slightly out and be sure that it’s seated properly and the niche is
free of debris, then install the light as described in step 5.
7. Connect the two (2) conductors to the corresponding circuit wires in the Junction Box (black wire to power, white wire to common) and secure the Junction Box cover in place.
8. Final check for proper light operation: Switch on the main switch or circuit breaker to the 12 VAC transformer and the switch that operates the light itself. The light should illuminate when 12 VAC power is applied. If not recheck the installation steps.
Install the light assembly:
Push the light into the niche while pulling the power cord from the junction box or transformer, making sure the locking tabs in the back end of the light are properly aligned with the niche openings (inside the niche).
Place the light installation tool over the front of the light. Turn the tool and light clockwise (less than an .3175 cm (1/8th. turn), while pushing inward, until you feel the stop point. This indicates the light is properly seated, locked and the niche is completely sealed. Note: If the light does not turn smoothly, pull the light slightly out and make sure that it’s seated properly and the niche is free of debris, then repeat this step.
Before operating the light, fill the pool with water until the light is completely submerged. Note: The light should not be powered for more than 30 seconds if is not submersed in water.
Final check for proper light operation: Switch on the main switch or circuit breaker to the 12 VAC transformer and the switch that operates the light itself. The light should illuminate when the 12 VAC power is applied. If not recheck the installation step.
Important Note:
Our 1.5" lights use a 14 gauge wire.
Troubleshooting Your 1.5 Inch Pool Lights Syncing Issues
If you're experiencing problems syncing your 1.5-inch pool lights or getting them to display the desired colors using your Pentair Intellitouch or Easytouch controller, don't worry! These lights are designed to mimic Pentair GloBrite functionality, so the following troubleshooting steps should help resolve most common issues.
Understanding the Issue
The primary challenge is ensuring the lights are all in the same color mode. When they're out of sync, your Pentair controller may struggle to coordinate them.
Troubleshooting Steps
-
Manual Synchronization via Wall Switch/Breaker:
- This method involves manually cycling through the color modes using the light's power source (wall switch or breaker).
- Key Principle: The lights change modes with each quick ON/OFF cycle.
-
Procedure:
- Start with the light switch in the "OFF" position.
- To select a specific mode, rapidly turn the switch ON and OFF the corresponding number of times.
- Important: Ensure the ON/OFF cycles are quick enough that the light does not fully illuminate during the process.
-
Color Mode Chart:
- 1 - White, magenta, blue and green colors
- 2 - Energy and excitement.
- 3 - Slow color transitions.
- 4 - Blues and greens
- 5 - Red, white and blue.
- 6 - Orange, red and magenta.
- 7 - Rich, deep color tones.
- 8 - Solid Blue
- 9 - Solid Green
- 10 - Solid Red
- 11 - Solid White
- 12 - Solid Magenta
- Example: To set all lights to "Red, white and blue" (mode 5), turn the switch ON and OFF five times rapidly.
- Goal: Repeat this process ensuring all lights are in the same color mode (ideally, start by setting both to solid white, mode 11).
-
Verify Pentair Controller Settings:
- Once all lights are manually synchronized, attempt to control them using your Pentair Intellitouch or Easytouch controller.
- Sync Function: Review your Pentair controller's user manual for instructions on using the built-in synchronization function. This feature is designed to align connected lights.
- Color Mode Selection: Ensure the desired color mode is correctly selected on the controller's interface.
-
Power Cycling:
- If the issue persists, try power cycling all of the lights and the Pentair controller.
- Turn off the breaker supplying power to the lights and the controller.
- Wait for approximately 30 seconds.
- Turn the breaker(s) back on.
- Attempt to synchronize the lights again using the Pentair controller.
-
Resetting the Light:
-
Quick On/Off: If power cycling doesn't work, try turning the light on and off rapidly (within 10-15 seconds of turning on) 31 times to reset the control board.
-
-
Wiring Check:
- If the steps above do not work, it is possible there is a wiring issue.
- Ensure all wiring connections to the lights and the Pentair controller are secure and correct.
- If you are not comfortable checking the wiring yourself, contact a qualified electrician or pool technician.
Important Notes:
- Rapid Cycling: The speed of the ON/OFF cycles is crucial for manual synchronization.
- Pentair Manual: Always refer to your Pentair controller's user manual for specific instructions and troubleshooting tips.
- Safety First: When working with electrical components, always ensure the power is turned off at the breaker to prevent electrical shock. If you feel uncomfortable working with electricity, please contact a professional.
By following these steps, you should be able to resolve most syncing issues with your 1.5-inch pool lights. If problems persist, please contact our customer support team for further assistance.